Pumps

Gear pumps series GHP1, GHP2 and GHP3

The pumps are simple, robust and affordable. Can be assembled with Borelli front bearing, electric and manual unlocking.

• Working pressure up to 290 bar
• Displacement 1.4 to 52 cm3 /rev.
• Tandem pumps from stock
• Right propelled by default
• Direction replaced easily
• The standard shaft is con 1:8

Silent gear pumps serie Elika

New external gear pump series from Marzocchi with patented conjugated helical tooth profile. The result is an outlet flow with very low pressure pulsations minimizing vibrations transmitted through air & pipework.Low number of teeth (seven) results in lower frequency pulsations that is less intriguing to the ear.

• Directly interchangeable with Marzocchi GHP2, GHP3 and ALP2, ALP3 pumps + other makes
• Hydrostatically balanced design for no axial loads.
• Unidirectional rotation
• Very high volumetric efficiency, little increase in volumetric loss over time.
• Inherent very good low speed characteristics.
• Pressure capability up to 300bar
• Wide range of shaft and flange options available.

Gear pumps series GHP2A with spline shaft

The pumps are simple, robust and affordable. Can be assembled with Borelli forsatslager, electric and manual unlocking.

• Working pressure up to 290 bar
• Displacement 1.4 to 52 cm3 /rev.
• Tandem pumps from stock
• Right propelled by default
• Direction replaced easily
• Spline Shaft

Internal gear pumps - series QX

The pumps are supplied with 2 - or 4-hole metric flange and straight shaft with a wedge. Also available as double and triple pump.

• Extremely low-noise pumps
• High efficiency
• Long life
• Very good suction characteristics
• Available for pumping chemicals

Internal gear pumps / motors series QXM

Intended for use as both pump and motor. Resistant to full working pressure at both ports. Suitable as a pump in a closed system if used in conjunction with variable speed electric motors for stepless pump flow.

• Very low noise
• Very high starting efficiency
• "0" pulsations

Internal gear pumps for low viscous liquids - series QXV

Specially designed for low viscosities and aggressive liquids. The unique design allows the liquid down to 1 cSt to be pumped because the pressure is built up incrementally as needed and therefore compensates leakage due to viscosity. The uniqueness of Truninger special pumps, are an extremely low noise level compared to other types of pumps for liquids of low viscosity. .

• Pumps liquid down to 1 cSt.
• Press building approx. 25 to 50 per element at 1-2 cSt.
• Max ca. 250 bar at approx. 1.5 to 2.0 cSt.
• Volumetric efficiency of approx. 65-70%
• Can pump diesel, gasoline, jet fuel, naphtha, "sub sea oil" etc.

DYNEX highpressure pumps for low viscosity fluid

High quality fixed desplacement checkball type piston pump. Extremely applicable for low viscosity fluid.

• Also available in stainless steel.
• Series PF1300 and PF4300
• Max operating pressure 1040 bar
• Specially designed for offshore and subsea applications.
• Displacement 0,79 to19,33 cm3/rev.
• Max speed 1.800 rpm.

Fixed piston pumps series SC12-108

Fixed axial type "bent axis" in sizes ranging from 12.6 to 108 cm3/omdr. Available in DIN or SAE design and can be directly mounted on the gear.

• Maximum working pressure 400 bar
• Powerful bearing
• Quiet pumps
• Available with by-pass valve

Fixed axial pump range PFX

Pumps of swach-plate design Available in several constructions also tandem.

• 420 bar max pressure
• 350 bar continuous pressure
• Displacement 66-250 cm3/rev.
• Powerful bearings-long life
• High efficiency
• Low noise
• Connection pressure side SAE 6000, SAE 3000 on suction side

Fixed axial pump series PFW

Pumps of swash-plate design for heavy use and long life. Available in several designs also tandem.

• 420 bar max pressure
• 350 bar continuous pressure
• Displacement 250-750 cm3/rev.
• Powerful bearings-long life
• High efficiency
• Low noise

EATON DuraForce™ HPR

Self-regulating Pump for Open Loop Operation

• Energy saving operation by “flow on demand” control
• Clockwise or counter clockwise rotation
• Self-priming at high nominal speed
• Higher rotating speed by tank pressurization or swashangle reduction
• Adaptive noise optimization SPU
• Noise optimization over the entire range of operation
• Dynamic response
• Excellent suction up to rated speed
• High pressure rating
• High reliability
• Long working life
• Compact design

Variable displacement axial piston pumps series 420 & 620

X20 series (420 & 620) are produced to meet increasing demands for compactness and increased power per. cm3 displacement.

• Maximum working pressure 280 bar
• Max pressure 320 bar intermitent
• Maximum peak pressure 350 bar.
• Light weight due to cost-effective construction

Variable axial piston pump, series of PVM

Variable displacement axial piston pumps for open circuit. A wide range of controls allows the pump can be adapted to many applications. The pumps have high efficiency, which means that the need for cooling is reduced.

• Max pressure 320 bar
• Maximum working pressure 280 bar
• Displacement from 18 to 141 cm3/rev.
• Low noise level and only 4% pressure pulsations
• Compact, space-saving pumps
• Standard with a maximum stroke limit
• Powerful bearings - long life
• Press Measuring point on the P-port
• Supplied with alternative pressure / flow control
• Suction port: SAE 3000 PSI and Pressure port: SAE 6000 PSI

Variable axial pump, series K3VL45 - 60-80 cm3/rev.

Pumps of Swash-plate type for open circuit, and parts and gasket sets.

• Max pressure 350 bar
• Continuous pressure 320 bar
• Max displacement adjustment as standard
• Wide range of regulators
• Controller for parallel execution of multiple pumps

Variable axial piston pumps, series K3VL 140-200 cm3/omdr.

Pumps of Swash-plate type for open circuit, and parts and gasket sets.

• Max pressure 350 bar
• Continuous pressure 320 bar
• Max displacement adjustment as standard
• Wide range of regulators
• Controller for parallel execution of multiple pumps

Variable axial piston pump, series K3VG

Pumps of Swash-plate design for open circuit. Available with different types of regulation. Also available as a "back to back" (DT), tandem pump with 360 cm3/omdr. or 500 cm3/omdr. Provides excellent speed characteristics, as well as the opportunity for sharing amount from the pump.

• Max pressure 400 bar
• Continuous pressure 350 bar
• Deplacement 180-560 m3/rev.
• Balanced spherical valve plate
• Hydrostatic balangsert bearing
• Max displacement adjustment as standard
• Wide range of regulators
• SAE 3000 PSI suction and SAE 6000 PSI pressure ports
• SAE 6000 samleflens available for DT pumps

Variable axial piston pump series V30E

V30E is a new generation of variable displacement axial piston pumps from Hawe-InLine.

• Max pressure 420 bar
• Continuous pressure 350 bar
• Displacement 98-270 cm3/rev.
• Compact design and light weight
• Very fast response time
• Quiet
• Comes with alternate pressure / flow control
• SAE 3000 PSI suction and SAE 6000 PSI pressure ports

Variable axial piston pumps, series of PVX

Pumps of Swash-plate design for open-circuit. Comes with many types of regulations, many designs, including continuous shaft for tandem installation.

• Max pressure 420 bar
• Continuous pressure 350 bar
• Displacement 66-250 cm3/rev.
• Powerful saving, long life
• High efficiency
• Low noise
• Connection pressure side SAE 6000, SAE 3000 suction side

Variable axial piston pumps series PVW

Pumps of Swash-plate design for open-circuit. Comes with many types of regulations, many designs, including continuous shaft for tandem installation.

• 420 bar max pressure
• 350 bar continuous pressure
• Displacemnet 250-750 cm3/rev.
• Powerful bearings for long life

Variable axial piston pumps series V60N

V60N is a variable displacement axial piston pumps for open circuit, designed for direct mounting on PTO, but is also available with SAE flange for standard installation.

• Max pressure 400 bar
• Working pressure 350 bar
• Displacement 90 and 110 cm3/rev.
• Very compact design
• Easy conversion to other rotation

Variable axial piston pumps series of PVH (Outgoing series)

PVH pumps are axial piston pumps with small dimensions and low weight. They are both in mobile and industrial design.

• 315 bar max pressure
• 275 bar working pressure
• Displacement 57, 74, 98 and 131 cm3/rev.
• Available with maximum pressure compensator, load sensing compensator and "Torque-Limiter"
• Ability to mount Cetop 3 control valve directly on the pump
• The pumps are available with cylindrical or spline shaft, also in the general design
• Connection flange SAE 3000 PS

InLine variable displacement axial piston pumps series V30D (Outgoing series)

Pumps of Swash-plate design for open circuit. Available with different types of regulation. Dual pumps available on request.

• Opp til 420 bar maks trykk
• Opp til 350 bar kontinuerlig trykk
• Fortregningsvolum 45-250 cm3/omdr.
• Up to 420 bar max pressure
• Up to 350 bar continuous pressure
• Deplacement 45-250 cm3/rev.

Variable displacement axial piston pumps

Axial piston pumps, series PVQ, are quiet pumps for industrial applications

• Max pressure 210 bar
• Deplasement from 10.5 to 45 cm3/omdr.
• Available with through-axle
• Can be used with alternative fluids
• Special patented "timing" arrangement for the reduction of pressure peakes/noise
• UNF Connection, and alternative metric thread
• Continuous speed 1800 rpm.

Variable axial piston type Medium Duty (outbound series)

70000-series pumps are designed for open circuit in both industrial and mobile applications. Comes with compensator of the type of maximum pressure limiting and load sensing compensator.

Parts axial piston pump series PVM

For each type of pump can be selected parts of the shaft and gasket set.

• All shafts have name starting with SAE J744-

Variable high pressure radial piston pump series RKP II.

RKPII ATEX is a new generation radial piston pump with sizes from 19 to 140 cm3

• Maximum continuous operating pressure 280 bar
• Displacement from 19 to 140 cm3 / rev
• Maximum speed 1800 rpm depending on size
• Also available as a double pump
• Compact design
• ATEX Exd version - see hydraulic subset "ATEX approved pumps"
• Low noise level 61 to 72 dB (A) depending on size
• Alternative fluids

Radial piston pumps with fixed displacement range of R

Deplacement 0,126 to 64,18 cm3/rev.. Radial piston pumps with fixed displacement has general application in hydraulic systems with performance up to 30 kW. Besides being able to be delivered as single pumps, they can also be supplemented with bellhousing and coupling and equipment for installation on or in the tank. Special versions where the oil is distributed to more outlets are available on request.

• Wide range of capacities at different pressures
• Pressure range up to 700 bar
• Rotation speed 100 - 2000 rpm. / Min. continuous
• indipendent of the direction of rotation
• BSP connections
• Available in special editions with several P-ports on the same pump

Variable high pressure radial piston pump series RKP. (Outgoing series)

RadialsRKP series is very quiet and can be delivered with a large variety of controllers.

• Maximum continuous operating pressure 280 bar
• Displacement from 19 to 140 cm3 / rev
• Maximum speed 1800 rpm depending on size
• Also available as a double pump
• Compact design

Transmission Pumps Series TVW

Axial pumps in swash plate design for closed circuit. Comes in many varieties, with a large selection of controls.

• Max pressure 420 bar
• Maximum working pressure 350 bar
• Displacement from 130 to 750 cm3/rev.
• Heavy duty shaft and bearing for long life
• Available in tandem design
• Complete valve equipment for closed circuit
• Press Filters on the feed circuit
• Wide range of pump controllers from simple hydraulic to digital PPQ regulators

Transmisjonspumper serie TVW - PpQ

Eaton axial P / TVW series for open or closed circuit can be supplied with prop. alternatively servo valve for regulating power, pressure and flow (PPQ). The corresponding digital control card prepared for current, voltage or Profibus control signal.
Pump range comes with displacement 130/180/250/360/500 cc. Alternatively, as a double pump.
Max pressure 420 bar. Max RPM 1800.
(Mounting / front flange interchangeable with A4V)

• Max pressure 420 bar
• Maximum working pressure 350 bar
• Displacement from 130 to 750 cm3/rev.
• Heavy duty shaft and bearing for long life
• Available in tandem design
• Complete valve equipment for closed circuit
• Press Filters on the feed circuit
• Wide range of pump controllers from simple hydraulic to digital PPQ regulators
• Digital PPQ regulators

Transmission Pumps TVX series

Variable axial piston pumps for closed systems.

• 420 bar max pressure
• 350 bar maximum working pressure
• Displacement from 66 to 180 cm3/rev.
• Heavy duty shaft and bearing for long life
• Available in tandem design
• Complete valve equipment for closed circuit
• Pressure Filters on the feed circuit
• Wide range of pump controllers from simple hydraulic to digital PPQ regulators

Transmission Pumps, Linde HPV-02 series

Axial pumps in swash plate design for closed circuit. Comes in many varieties, with a large selection of modular controls.

• Max operating pressure 420 bar
• Max peek pressure 500 bar
• Maximum continuous working pressure 250 bar delta P.
• Displacement from 55 to 280 cm3/rev.
• 21° swash angel design gives compact build size and log service life.
• Hydrostatic bearing compensate for axial forces.
• Available in tandem design
• Filters on the feed circuit

Transmission Pumps TVX series

Variable axial piston pumps for closed systems.

• 420 bar max pressure
• 350 bar maximum working pressure
• Displacement from 66 to 180 cm3/rev.
• Heavy duty shaft and bearing for long life
• Available in tandem design
• Complete valve equipment for closed circuit
• Pressure Filters on the feed circuit
• Wide range of pump controllers from simple hydraulic to digital PPQ regulators

Transmission pumps Series Medium Duty

Varaible axial piston pumps for closed systems, supplied as single or double pumps.

• Up to 380 bar max pressure
• 210 bar maximum working pressure
• Displacement from 20.3 to 49.2 cm3/rev.
• Available with feed pump
• Integrated pressure relief valve

Vane pumps series VMQ2 + VMQ3

The pumps are available as single, double or triple pumps and single pumps with through-axle. Interchangeable inserts makes the pump very flexible with respect to the choice of fluid flow. Single pumps, see information on VMQ1.

• Max. working pressure 290 bar.
• Easily change direction of rotation.
• Low noise
• Multiple axle types: V / splines - SAE / ISO.
• The ports can be placed in different positions relative to each other by 90 degrees step.
• Metric 4-bolt flanges (ISO 6162.
• The default maximum speed is 1800 rev/min.

Vane pums series VMQ1

The pumps are available as single, double or triple pumps and single pumps with through-axle. Interchangeable inserts makes the pump very flexible with respect to the choice of fluid flow. Double and triple pumps, see information on VMQ2 + VMQ3.

• Max. working pressure 290 bar.
• Easily change direction of rotation.
• Low noise
• Multiple axle types: V / splines - SAE / ISO.
• The ports can be placed in different positions relative to each other by 90 degrees step.
• Metric 4-bolt flanges (ISO 6162).
• The default maximum speed is 1800 rev/min.

Vane pumps, medium pressure series VQH

VQH series compared to previous VQ/-20 design series upgraded cartridgekit pump housing and high-strength cast iron.

• The result is higher peak pressure and improved volumetric efficiency.
• Installation dimensions are identical to the VQ / - 20 design and cartridge kits are also interchangeable.
• VQH series consists of fixed wing single and double pumps.
• Dual pump pressure values in blank table, see the individual pumps.
• Also available with through-axle.

Vane Pumps Series VQ Single Pump (Replaced by VQH)

Displacement 39-193 cm3/rpm - Vane pumps of "intra-vane" type for industrial and mobile applications.

• Maks. arbeidstrykk 210 bar
• Fleksible bi-metall sideplater gir optimale kaldstartegenskaper
• Innsatser utskiftbare med innsatser fra industriell vingepumpe serie "V"
• Omdr. tall maks. 2700 omdr./min.
• Tilkobling SAE 3000 flenser
• Kan leveres som dobbelpumpe og med gjennomgående aksel
• Max. working pressure 210 bar.
• Flexible bi-metal side panels for optimal cold start characteristics.
• Inserts with interchangeable inserts from industrial wing pump series "V".
• Speed max. 2700 rpm.
• Connection SAE 3000 flanges.
• Available as double pump and through-axle

Vane pumps series VQ Dobble pumps (Replaced by VQH)

Displacement 39-193 cm3/rev. Vane Pumps of "intra-vane" type for industrial and mobile applications.

• Max. working pressure 210 bar.
• Flexible bi-metal side panels for optimal cold start characteristics.
• Inserts with interchangeable inserts from industrial wing pump series "V".
• Speed max. 2700 rev/min
• Connection SAE 3000 flanges.
• Available as a single pump, see information about the wing pump series VQ1.

Vane Pumps Series VQ Double Pump (Replaced by VQH)

Displacement 39-193 cm3/rev. Vane pumps of "intra-vane" type for industrial and mobile applications.

• Max. working pressure 210 bar.
• Flexible bi-metal side panels for optimal cold start characteristics.
• Inserts with interchangeable inserts from industrial wing pump series "V".
• Speed max. 2700 rev/min
• Connection SAE 3000 flanges.
• Available as a single pump, see information about the wing pump series VQ1.

Vane Pumps Series V10 and V20

Displacement from 6.55 to 41.8 cm3/rev. Vane pumps for mobile and industrial applications.

• Max. working pressure 170 bar.
• V10 and V20 are wing pumps with fixed displacement.
• Balanced design minimizes bearing load.
• Silent operation.
• Can run on alternative fluids.
• Supplied as single and double pumps.

Vane Pumps Series V (Replaced by VQH)

Displasement 39-193 cm3/rev. Vane Pumps of "intra-vane" type for industrial applications.

• 12 wings kit.
• Low noise.
• Removable inserts make the pump flexible.
• Speed, max. 1800 rev/min.
• Connection SAE 3000 flanges.

Parts vane pumps, single type VQ

For each type of pump can be selected parts of the shaft, gasket kit, bearings and kit.

Parts vane pump VQ double

For each type of pump can be selected parts of the shaft, gasket kit, bearings and kit.

Parts vane pumps type VMQ

For each type of pump can be selected parts of the shaft, gasket kit and kit.

Hand pump series HP11

Hand pumps for most applications, body in aluminum. Also available with tank.

• Connection suction side G 3/8, pressure side G 1/4
• With the safety valve, relief valve and check valve
• Can be mounted below the oil level

Hand pumps series HP30, HP60 og HP100

Solid hand pumps in steel.

• Double-acting with non-return valve.
• Can be mounted in any position
• Available with fixed or telescopic handle with locking in the inner and outer positions
• Can be supplied with mounting flanges for tank lid (A flange) and the tank side assembly (std)

Radial piston pumps with fixed displacement range of R

Deplacement 0,126 to 64,18 cm3/rev.. Radial piston pumps with fixed displacement has general application in hydraulic systems with performance up to 30 kW. Besides being able to be delivered as single pumps, they can also be supplemented with bellhousing and coupling and equipment for installation on or in the tank. Special versions where the oil is distributed to more outlets are available on request. ATEX approved

• ATEX approved
• Wide range of capacities at different pressures
• Pressure range up to 700 bar
• Rotation speed 100 - 2000 rpm. / Min. continuous
• indipendent of the direction of rotation
• BSP connections
• Available in special editions with several P-ports on the same pump

ATEX Variable axial piston pump, series of PVM

Variable displacement axial piston pumps for open circuit. A wide range of controls allows the pump can be adapted to many applications. The pumps have high efficiency, which means that the need for cooling is reduced.

• Max pressure 320 bar
• Maximum working pressure 280 bar
• Displacement from 18 to 141 cm3/rev.
• Low noise level and only 4% pressure pulsations
• Compact, space-saving pumps
• Standard with a maximum stroke limit
• Powerful bearings - long life
• Press Measuring point on the P-port
• Supplied with alternative pressure / flow control
• Suction port: SAE 3000 PSI and Pressure port: SAE 6000 PSI
• ATEX certified

Atex variable axial piston pump series V30E

V30E is a new generation of variable displacement axial piston pumps from Hawe-InLine.

• Max pressure 420 bar
• Continuous pressure 350 bar
• Displacement 98-270 cm3/rev.
• Compact design and light weight
• Very fast response time
• Quiet
• Comes with alternate pressure / flow control
• SAE 3000 PSI suction and SAE 6000 PSI pressure ports
• Atex certified by Servi Group

Atex variable aksialstempelpumper serie K3VL 140 - 200 cm3/omdr.

Pumps of Swash-plate type for open circuit, and parts and gasket sets.

• Max pressure 350 bar
• Continuous pressure 320 bar
• Max displacement adjustment as standard
• Wide range of regulators
• Controller for parallel execution of multiple pumps
• Atex certified by Servi Group

ATEX DYNEX highpressure pumps for low viscosity fluid

High quality fixed desplacement checkball type piston pump. Extremely applicable for low viscosity fluid.

• Also available in stainless steel.
• Series PF1300 and PF4300
• Max operating pressure 1040 bar
• Specially designed for offshore and subsea applications.
• Displacement 0,79 to19,33 cm3/rev.
• Max speed 1.800 rpm.

Atex variable aksialstempelpumper serie K3VL45 - 60 - 80 cm3/omdr.

Pumps of Swash-plate type for open circuit, and parts and gasket sets.

• Max pressure 350 bar
• Continuous pressure 320 bar
• Max displacement adjustment as standard
• Wide range of regulators
• Controller for parallel execution of multiple pumps
• Atex certified by Servi Group

Atex tannhjulspumper for lavviskose væsker - innerfortannet serie QXV

Specially designed for low viscosities and aggressive liquids. The unique design allows the liquid down to 1 cSt to be pumped because the pressure is built up incrementally as needed and therefore compensates leakage due to viscosity. The uniqueness of Truninger special pumps, are an extremely low noise level compared to other types of pumps for liquids of low viscosity.

• Pumps liquid down to 1 cSt.
• Press building approx. 25 to 50 per element at 1-2 cSt.
• Max ca. 250 bar at approx. 1.5 to 2.0 cSt.
• Volumetric efficiency of approx. 65-70%
• Can pump diesel, gasoline, jet fuel, naphtha, "sub sea oil" etc.
• Atex certified by Servi Group

Atex tannhjulspumper - innerfortannet serie QX

The pumps are supplied with 2 - or 4-hole metric flange and straight shaft with a wedge. Also available as double and triple pump.

• Extremely low-noise pumps
• High efficiency
• Long life
• Very good suction characteristics
• Available for pumping chemicals
• Atex certified by Servi Group