Motors

Fixed displacement motors for open and closed loop applications.

Axial piston motor in swashplate design for high pressure open and closed loop systems. Optimized starting and low speed behaviour.

• Steady low speed
• High starting torque
• Compact design
• High power density
• High reliability
• Long service life

Variabel displacement motors for open and closed loop applications.

Axial piston motor in swashplate design for high pressure closed and open loop systems. Optimized starting and low speed behaviour.

• Jerk-free low speed
• High starting torque
• Large conversion range
• Zero angle possible
• Dynamic response
• PTO through-drive motor
• Compact design
• High power density
• High reliability
• Long service life

Fixed axial series SCM

Supplied with both frontflens and withdrawn flange (cartridge version). Very robust axial piston motors.

• Compact design, high starting torque and high reliability
• Displacement from 12 to 130 cc
• Maximum continuous operating pressure 350 bar
• Maximum speed 8000 to 4700 rev / min depending on size
• Allows for high axle load
• The engine is particularly suitable where there is a requirement for rapid changes of speed and direction of rotation
• SAE connections marked with * are supplied with 6000 PSI
• SAE or ISO standard flanges and shafts
• See respective data sheet for code-breaking

Fixed radial piston motors range HMB

Fixed displacement 188-11600 cm3/rev. Slowly propelled motors with rotating shaft. Supplied as standard with a straight shaft and key, is also available with spline or tapered shaft.

• High starting torque
• Compact and robust design
• Powerful store allows large lateral forces
• Very smooth running at low
• Available with output for tachometer
• Shaft seal for elevated pressure drain can be delivered
• Available with brake and gear

Variable radial piston motor series HMC

Variable displacements. 492 - 5326 mc3/rev. Ability to shift between two displacements. or alternatively continuous variable between two displacements. Can be supplied with constant power regulating valve (CHP), or with el.proporsjonal valve (CVM) for full control of displacements.

• High starting torque
• Compact and robust design
• Powerful bearings allows large lateral forces
• Very smooth running at low speed
• Available with socket for mounting tachometer
• Shaft seal for raised drain pressure can be delivered
• Can also be supplied with brake and gear

Variable axial piston motor HPC

HPC Series is designed to meet increasing demands for maximum effect. In addition, higher initial efficiency motor / mechanical efficiency. Motor series is also designed to withstand higher back pressure. Available in displacement from 1600 to 5326 cm3/rev. For more information see data sheet.

Fixed radial piston motors range MHA

Slow running motors with rotating shaft.

• Smooth operation at very low speeds
• Large speed ratio
• High volumetric efficiency
• High starting torque
• Powerful bearings allows large axial and radial forces
• Few moving parts
• Can be used with non-flammable liquids
• Wheel Motor version is available
• Different brakes available

Fixed radial piston motor series KM and RM

Very robust motor range as suitable for heavy demanding duties By default, a powerful front-mounted bearing to take up the axial and radial forces. Depl 11 to 251 cm3/rev.

• Fixed displacement volume from 11 - 251cm3
• Lagsomtgående motors with rotating shaft.
• Additional shaft options.
• Compact and robust design.
• Very smooth run at low speeds.
• Can be used with non-combustible liquids.
• Can also be used with water-based oils and subsea oil.
• See data sheet for details.

Gerotor H series motors

Char-Lynn motor is of the gerotor type, combines high performance with low initial cost. Motors are stocked with SAE-A 2-bolt flange, G 1/2 "connections and 25mm axle.

• Deplacement 36-370
• Torque up to 520 Nm
• Speed ??up to 1100 revs. / Min.
• Maximum inlet pressure 175 bar
• Allowed return pressure without drain 105 bar
• Recommended purity ISO 18/13
• Optimum viscosity 24-43 cSt
• Valves flanges can be supplied
• Corrosion protected shaft is supplied from stock on some models

Gerola motors series S

Char-Lynn motor that is gerolertype combines high performance with low acquisition costs. Motors are stocked with SAE-A 2-bolt flange, G 1/2 "connections and 25mm axle.

• Deplacement 59-370 cm3/rev.
• Torque up to 515 Nm
• Speed ??up to 1150 revs. / Min.
• Maximum inlet pressure 175 bar
• Allowed return pressure without drain 105 bar
• Recommended purity ISO 18/13
• Optimum viscosity 24-43 cSt
• Valves flanges can be supplied

Gerolermotorer series J2

Char-Lynn gerolermotor J2 Series combines small dimensions with high performance. motor is the smallest in the Eaton's series of gerolermotorer have high starting torque and the same torque regardless of the direction of rotation.

• Displacement Volume from 8.2 to 19.8 cm3/rev.
• Torque up to 61 Nm
• Speed ??up to 2535 revs. / Min.
• Maximum inlet pressure 200 bar
• Allowed return pressure without drain 70 bar
• Recommended purity ISO 18/13
• Optimum viscosity 24-43 cSt
• 2-bolt montasjeflens
• Standard shaft diameter dimension of 16mm
• Spline shaft on request

Gerolermotorer series T

Char-Lynn motor is gerolertype, is a compact motor at the same time the performance is higher than other similar motors Motors are stocked with SAE-A 2-bolt flange, G 1/2 "connections and 25mm axle.

• Deplacement 36-370 cm3/rev.
• Torque up to 510 Nm
• Speed ??up to 1155 revs. / Min.
• Maximum inlet pressure 175 bar
• Allowed return pressure without drain 105 bar
• Recommended purity ISO 18/13
• Optimum viscosity 24-43 cSt
• Valves flanges can be supplied
• Corrosion protected shaft is supplied from stock on some models

Gerolermotorer Series 4000 Compact

Char-Lynn high torque low speed motors in the "compact" version. Same description as provided satndard 4000 but with size as a 2000 engine

• Deplacement 160-490 cm3/rev.
• Allowed return pressure without drain 140 bar
• Recommended purity ISO 18/13
• Optimum viscosity 24-43 cSt
• Two speed motors available
• Valves flanges are available

Gerolermotorer Series 4000

Reliable low speed high torque Char-Lynn motors, disc valve type. Motors are stocked with SAE-C 4-bolt flange, G 3/4 "connections and 40mm axle. Also available as a wheel motor that manages high side loads and without bearings for direct mounting on gear

• Fortrengningsvolum 110 - 625 cm3/omdr.
• Vrimoment opp til 1800 Nm
• Turtall opp til 860 omdr./min.
• Maks innløpstrykk 310 bar
• Tillatt returtrykk uten drenering 105 bar
• Anbefalt renhetsgrad ISO 18/13
• Optimal viskositetsområde 24-43 cSt
• Ventiler for flensmontasje er tilgjengelig

Gerolermotorer Series 6000

Reliable low speed high torque Char-Lynn motors, disc valve type. Motors are stocked with SAE CC 4-bolt flange, G 1 "connections and 40mm axle. Also available as a wheel motor that manages high side loads and without bearings for direct mounting on gear

• Deplacement 195-985 cm3/rev.
• Torque up to 1885 Nm
• Speed ??up to 860 revs. / Min.
• Maximum inlet pressure 310 bar
• Allowed return pressure without drain 105 bar
• Recommended purity ISO 18/13
• Optimum viscosity 24-43 cSt

Gerolermotorer Series 10000

Reliable low speed high torque Char-Lynn motors, disc valve type. Motors are stocked with SAE CC 4-bolt flange, SAE 1 1/4 "connections and 2 1/4" tapered shaft, SAE J501 Also available as a wheel motor that manages high side loads and without bearings for direct mounting on gear

• Deplacement 345-940 cm3/rev.
• Vrioment up to 2700 Nm
• Speed ??up to 780 revs. / Min.
• Maximum inlet pressure 275 bar
• Allowed return pressure without drain 20 bar
• Recommended purity ISO 18/13
• Optimum viscosity 24-43 cSt
• Two speed motors available
• Valves flanges available

Gerolermotorer series T with built-in brake

• Deplacement 36-370 cm3/rev.
• Torque up to 510 Nm
• Speed ??up to 1155 revs. / Min.
• Maximum inlet pressure 155 bar
• Recommended purity ISO 18/13
• Integrated brake in the rear with a 6:1 exchange as a result of gerolerdesign
• Brake Torque 2000 to 5000 Nm depending on size and design

Gerolermotorer Series 2000

Reliable low speed high torque Char-Lynn motors, disc valve type. Motors are stocked with 4-bolt flange, G 1/2 "connections and 32mm axle. Also available as a wheel motor that manages high side loads and without bearings for direct mounting on gear

• Deplacement 80-490 cm3/rev.
• Torque up to 900 Nm
• Speed ??up to 920 revs. / Min.
• Maximum inlet pressure 310 bar
• Allowed return pressure without drain 140 bar
• Recommended purity ISO 18/13
• Optimum viscosity 24-43 cSt
• Two speed motors available
• Valves flanges are available

Gear motors Series GHM

Motors are simple, robust and affordable. Can be assembled with Borelli bearings, electrical or mechanical unlocking

• Displacemnet 2.8 to 87.6 cm3/rev.
• Reversible motors
• The standard shaft is tapered 1:8
• Can be delivered with other shafts
• Available with SAE flanges

HPI Gear Motor

broad range from 0.5 to 250 cm3/rev. Peak pressure up to 250 bar.

• Very good starting torque characteristics.
• Available with according to ISO, DIN, SAE or "Italian" standard.
• Minimum viscosity 12cSt, Maximum 150cSt
• Temperature range -20 degrees to +80 degrees.
• Also available with Viton seals.

Gear motors Series GHM

Simple, compact and robust motors for a wide range of applications

• Displacement from 2.8 to 87 cm3/rev.
• 1:8 Tapered shaft is standard. Alternative perform requests are also available.
• Motor housing in high-strength aluminum
• Frontflens and the back lid of the iron
• Girsett are made of hardened special steel

Haldex gear flow dividers

Effective gear dividers Available number of chamber: 2.3 and 4 Is normally supplied with internal trykkutgjevningsventil No separate drain. Can also be used as a pressure amplifier.

• GC series:
• Sizes available from 1.6 cm3 to 8.5 cm3
• Diff Max pressure: 124 bar. In Max pressure: 207 bar Max out pressure: 241 bar
• Recommended speed range: 2,000 - 3.500rpm
• D series:
• Sizes available from 3.8 cm3 to 13.3 cm3
• Diff Max pressure: 207 bar In Max pressure: 207 bar Max out pressure: 310 bar
• Recommended speed range: 2,000 - 4.000rpm
• See data sheet for further details.

Rotary Actuator Series DA-H

A rotary actuator can often provide a far more elegant and compact solution than the use of cylinder / torque arm or engine / transmission solution.

• 20 sizes from 36 to 250000 Nm with pistons Ø 40– Ø 450 mm
• 4 rotary angle rages for each size: 90°, 180°, 270° and 360°
• Actuator shaft with 2 feather keys or DIN 5480 involute spline
• Tandem seal on the actuator shaft
• Available with position sensor
• Available with angel adjustment HKS speciality is to make custom solution for your application, based on the new DA-H1 design!!!